Mwrf 976 34pteaser 0
Mwrf 976 34pteaser 0
Mwrf 976 34pteaser 0
Mwrf 976 34pteaser 0
Mwrf 976 34pteaser 0

Spectrum Inversion Ensures Compliance With 3GPP2

Oct. 11, 2013
Spectrum inversion is used in 3GPP2 communications systems and can be implemented with various transceivers through the use of three simple methods.

Related Articles
Digital Predistortion Linearizes RF PAs
Synthesizer Serves MB-OFDM UWB
Perfect A PLL LTE Synthesizer

Spectrum inversion is part of the physical layer in Third Generation Partnership Program 2 (3GPP2) using NCDMA techniques, prior to transmissions and following signal reception. Due to the large number of available RF transceivers and baseband processors on the market, it is easy to see how RF transceivers and baseband processors could easily have mismatched spectrum in both the transmit and receive paths. Such a simple oversight will result in noncompliance with the 3GPP2 standard and failure to achieve signal demodulation. Fortunately, for those involved with 3GPP2 systems, a few simple techniques can help determine if spectrum inversion has been performed on a signal. Three simple techniques are also presented to help perform spectrum inversion on RF transceivers that do not have built-in spectrum inversion.

In a transmitter, the easiest way to determine whether the spectrum has been inverted is by comparing a single-tone continuous-wave (CW) wave with nominally positive frequency to the local-oscillator (LO) frequency. If the RF CW output frequency is greater than the LO frequency (a positive offset), then no spectrum inversion has occurred. But if the LO frequency is greater than the RF output frequency, the spectrum has been inverted.

1. This shows the WCDMA I/Q modulation and demodulation format. The Q channel is multiplied by a negative phase LO (i.e., -sin(ωLOt), as shown in the red.

In the receive path, if a positive offset RF input frequency produces an in-phase (I) output that leads the quadrature (Q) output by 90 deg., then no spectrum inversion was performed by the RF demodulator. Generally, the modulation format of the RF demodulator follows the modulator. These points can be demonstrated by examining the uplink and downlink paths of a WCDMA system, as specified in the 3GPP standard TS 25.213 (Fig. 1). For simplicity’s sake, assume that the transmitter baseband I and Q signals are represented by the expression:

Vm = emt = cos(ωmt) + jsin(ωmt)

where this is a positive frequency, yielding a complex tone at baseband. The transmitter’s I and Q LO signal components are represented by the expression:

LOITX = cos(ωmt) and

LOQTX = -sin(ωmt)

Next, notice the negative polarity of the Q LO signal: 

VTX = cos(ωmt)cos(ωLOt) - sin(ωmt)sin(ωLOt)

VTX = 0.5cos[(ωm - ωLO)t] + 0.5cos[(ωm + ωLO)t] - 0.5cos[(ωm - ωLO)t] +(ωm + ωLO)t]

and

VTX = cos[(ωm + ωLO)t]

As these expressions reveal, a positive modulation baseband signal, in combination with a negative-phase LO frequency, produces an RF output frequency which resides above the LO frequency. The result is no spectrum inversion.

On the receiving end, assume that the same transmitted RF signal is received and demodulated with the same LO format as the transmitter:

VRX = cos(ωRX)t

with

ωRX = ωm + ωLO

VLO = e-jωLOt  = cos(ωLOt) - jsin(ωLOt)

VBB = cos(ωRXt)cos(ωLOt) - jcos(ωRXt)sin(ωLOt)

After multiplying out the terms and applying lowpass filtering to remove higher-frequency signal components:

VBBI = 0.5cos[(ωRX - ωLO)]t]

and

VBBQ = 0.5sin[(ωRX - ωLO)]t]

Substituting ωRX with ωm + ωLO, the I and Q baseband outputs are the same as the I and Q transmit baseband inputs:

Im = cos(ωmt)

and

Qm = sin(ωmt)

A Plan Of Action

With a clearer understanding of how to detect spectrum inversion, it is now time to explore available methods for achieving it. As mentioned earlier, the 3GPP2 standard requires that the signal spectrum of NCDMA be inverted prior to transmission and after reception. Three simple methods can be used for spectrum inversion.

2. This shows the NCDMA I/Q modulation format. The Q channel is multiplied by the LO with positive phase (i.e., sin(ωmt), as highlighted in the red.

In the first method, spectrum inversion is achieved by adopting a positive phase LO. This is the modulation format recommended by the 3GPP2 standard (Fig. 2):

Im = cos(ωmt)

and

Qm = sin(ωm)

and

LOITX = cos(ωLOt)

and

LOQTX = sin(ωLOt)

VTX = cos(ωmt)cos(ωLOt)  + sin(ωmt)sin(ωLOt)

VTX = 0.5cos[(ωm) - ωLO)]t + 0.5cos[(ωm + ωLO)]t + 0.5sin[(ωm - ωLO)]t + 0.5sin[(ωm + ωLO)]t 

VTX = cos[(ωm) - cos(ωLO)t] 

As shown here, the RF output frequency is lower than the LO frequency. Therefore, the spectrum has been inverted.

In method 2, spectrum inversion is achieved by inverting the polarity of the Q baseband signal:

Im = cos(ωmt)

and

Qm = -sin(ωmt)

LOITX = cos(ωLOt)

and

LOQTX = -sin(ωLOt)

VTX = cos(ωmt)cos(ωLOt)  + sin(ωmt)sin(ωLOt)

VTX = 0.5cos[(ωm) - ωLO)]t + 0.5cos[(ωm + ωLO)]t + 0.5cos[(ωm - ωLO)]t - 0.5cos[(ωm + ωLO)]t 

VTX = cos[(ωm - ωLO)t] 

In the third method, spectrum inversion is achieved by swapping the I and Q transmit baseband signals:

Im = sin(ωmt)

and

Qm = cos(ωmt)

LOITX = cos(ωLOt)

and

LOQTX = -sin(ωLOt)

VTX = cos(ωmt)cos(ωLOt)  + sin(ωmt)sin(ωLOt)

VTX = 0.5sin[(ωm) + ωLO)]t + 0.5sin[(ωm - ωLO)]t - 0.5sin[(ωm + ωLO)]t + 0.5sin[(ωm - ωLO)]t 

VTX = cos[(ωm - ωLO)t] 

Related Articles
Digital Predistortion Linearizes RF PAs
Synthesizer Serves MB-OFDM UWB
Perfect A PLL LTE Synthesizer

Method 1 is the approach recommended by the 3GPP2 standard for performing spectrum inversion. However, as shown above, other methods can achieve the same result and still be compliant with the specifications. In all cases for parts derived from the MAX2553 WCDMA transceivers from Maxim Integrated™, the baseband input and output pins are labeled so that no spectrum inversion occurs in the transceiver—either in the transmitter or receiver path. For compliance with the 3GPP2 standard, one should be aware of this and apply one of the above methods for inverting the transmit spectrum. For the receive path, a corresponding inversion is also required in most cases, unless the baseband is already programmed to accept inverted spectrum signals.

Sponsored Recommendations

Frequency Modulation Fundamentals

March 14, 2024
The development of crystal-clear FM communications was an innovation of genius and toil. Utilized today in applications such as radar, seismology, telemetry and two-way radios...

44 GHz Programmable Signal Generator

March 14, 2024
The Mini-Circuits SSG-44G-RC is a 0.1 to 44 GHz signal source with an RF output range of -40 to +17 dBm with fine resolution. This model supports CW and pulsed (? 0.5 ?s) outputs...

50W SSPA with Built-In Signal Source & Control

March 14, 2024
The RFS-2G42G5050X+ takes Mini-Circuits robust line of solid state, connectorized, high-power amplifiers for RF energy to a new level by integrating the versatility of a signal...

Webinar: Introduction to OTA Measurement for mmWave and Sub-THz

Feb. 19, 2024
Join Jeanmarc Laurent, a leading expert from MilliBox, for an exclusive live webinar showcasing a complete Over-the-Air (OTA) testing system setup. In this immersive session, ...