Direct-conversion architectures enable the broadband radios needed to support multimode, multiple standards in third-generation (3G) and fourth-generation (4G) wireless networks. The capability of handling signals from 400 MHz to 4 GHz across the globe has pushed infrastructure and mobile-device developers to seek new levels of performance for the components in those systems. Fortunately, improved silicon germanium (SiGe) and CMOS semiconductor processes are allowing higher levels of integration with low power consumption. And a direct-conversion architecture enables a radio designer to cover a large frequency range and with scalable bandwidths on a single hardware platform. It offers many advantages over traditional IF-sampling receiver approaches for wireless base stations, and combined the benefits of a balanced and blocker-immune RF demodulator with analog-to-digital converter (ADC) technology utilizing adaptive correction techniques for the residual signal impairments.

The 3G Long Term Evolution (LTE) wireless communications standard supports a variety of channel bandwidths from 1.4 to 20 MHz. A minimum bandwidth requirement of 20 MHz is commonly used, whether the equipment supports LTE-only carriers or a mix of 3G (WCDMA) or LTE (OFDM) carriers. Such wide bandwidth allows multiple adjacent or nonadjacent carriers to be received. For example, as many as four adjacent WCDMA signals can crowd a 20-MHz bandwidth.

The challenges of a broadband receiver design lie in the capability to demodulate low-level, high-datarate signals in the presence of high interfering signals. By definition, a multicarrier RF receiver has no analog channel selectivity, and unwanted blockers reach the ADC without being attenuated. This leads to high dynamic-range requirements for the receiver building blocks, especially the ADC. For instance, a 3G LTE blocking requirement calls out narrowband blockers 60 dB above the desired signal. As a result, a multicarrier receiver should have a high input 1-dB compression point, high-resolution ADCs, and some form of automatic gain control (AGC) to maintain blocker signal levels below the full-scale (FS) level of the ADC.

This immunity to blockers must be achieved along with acceptable receiver sensitivity. A base-station receiver designed to support the 3G LTE standard must have a noise figure (NF) of better than 5 dB. To reach this level of performance with margin, the downconverting mixer or demodulator is typically preceded by a few low-noise-amplifier (LNA) stages. Front-end gain helps improve the overall NF according to the Friis equation:

NFtotal = NFLNAs + (NFdemod - 1)/ GLNAs+ADC -1/(GLNAsGdemod)> (1) However, front-end gain cannot be set arbitrarily high since a strong blocking signal at the antenna could bandcause receiver saturation. Also, excessive gain can degrade linearity and affect signal integrity when intermodulation products from high-level blockers fall within the desired signal bandwidth. A suitable quadrature demodulator must provide a good balance between noise figure and linearity, as measured by the third-order intercept point (IP3).

Quadrature demodulator amplitude and phase errors can cause inband images or unwanted sideband energy. In a multicarrier receiver, strong in-band interfering signals may be adjacent to modulated carriers at the receiver sensitivity level. Maintaining adequate amplitude and phase balance through the baseband demodulation process is critical to good receiver performance. The image-rejection requirement is determined by the difference between the strongest and weakest in-band signals, the required signal-to-noise ratio (Eb/No) for demodulation, and margin for other noise contributions. The 3G LTE standard calls for at least 60-dB total image rejection. Reciprocal mixing in a broadband receiver is also an important phenomenon to consider when specifying demodulator localoscillator (LO) phase noise. The LO phase noise modulates nearby unfiltered blockers, adding Pblocker_dBm - LO_Noise dBc/Hz noise to the wanted channel.

A direct-conversion signal chain (Fig. 1) provides a low-cost receiver solution for 3G and 4G systems. It is a less complex architecture than other receivers, not requiring the multiple surface-acousticwave (SAW) and discrete filters used in a real IF sampling architecture. The baseband channel filter is typically a discrete lowpass design that provides both out-of-band blockers and broadband noise rejection before digitization. It can be designed with much lower insertion loss and cost than the IF filters used in super-heterodyne or real- IF sampling architectures. With an I/Q demodulator, the baseband cutoff frequency need only to be one-half of the total signal bandwidth for a complex modulated signal centered at 0 Hz.

For example, assume the multicarrier RF input signal at the receiver antenna is a nonsymmetrical doublesideband signal centered on a carrier frequency F0. A quadrature demodulator operating at LO = F0 converts the real RF signal into a complex baseband signal. It generates both the real and imaginary components at the difference and sum frequencies LO+/- F0 or 0 Hz and 2F0. Lowpass filters remove the sum terms, signal harmonics, and noise before analog-to-digital conversion. If the total signal bandwidth is Bx, then the filter cutoff frequency should be set at Fc> Bx/2.

Another key advantage of a directconversion approach is the lower ADC sampling rate requirement since the I/Q signal bandwidth is only onehalf the total composite signal bandwidth. With downconverted signals centered at DC, the sampling theory then requires a sampling rate at least 2(Bx/2) or Bx, which is one-half of the minimum sampling rate required by an IF sampling receiver for the demodulation of the same bandwidth. For a 20-MHz-capable LTE receiver, this corresponds to a Nyquist sampling rate over 20 MHz for each I and Q path (Fig. 2).

Despite the advantages, directconversion radio design does not come without difficulty. Any gain or phase imbalance on the I and Q paths or non-exact 90-deg. phase shift of the demodulator circuit will result in energy at the unwanted sideband frequency. When such a receiver downconverts the desired multicarrier signals around zero Hz (zero-IF), the desired carriers will be on both sides of DC (Fig. 3). Carrier 1 image around DC appears on the next channel where a weaker carrier may be present. Poor image rejection will therefore limit the receiver sensitivity if no digital calibration is used. Anti-alias filter components tolerance may also impact the overall image rejection performance. Until recently, it was quite difficult to achieve acceptable levels of gain and phase balance over a wide bandwidth. Newer SiGe process technologies enable high-quality RF performance to 6 GHz for the demodulator's active mixer cells.

In the baseband down-conversion process, some energy is generated at DC through the quadrature modulator. Any LO signal leaking back to the RF input mixes with that same LO signal, resulting in a DC component. Demodulating the RF carriers to a multiple of one-half of the channel bandwidth is one way of avoiding co-channel DC offsets. The DC component amplitude should not impair the receiver's ability to receive weak signals.

As part of a direct-conversion receiver, the ADL5380 and ADL5382 I/Q demodulators from Analog Devices were designed to achieve broadband operation with optimum LO leakage and image suppression. Ideally, the demodulator implements a single-sideband mixing operation with two mixers. An amplified local oscillator (LO) signal is fed directly to the first mixer, while that same signal, shifted by 90 deg., is fed to the second mixer.

To meet the performance specifications with sufficient margin, the I/Q demodulator employs an optimized LO buffer and phase-shifter circuit. Its innovative circuit topology maintains an accurate 90-deg. phase shift over a wide frequency range, while maintaining circuit noise below the phase noise from the LO PLL. The design is optimized for minimum AM/PM distortion, making it insensitive to LO drive level with enhanced secondorder distortion performance.

Continue to page 2

Page Title

The ADL5380's LO-to-RF leakage was measured as better than -50 dBm to 3 GHz while the ADL5382 I/Q demodulator achieves even lower leakage performance, exceeding -60 dBm to 2.3 GHz. The gain imbalance is better than +/-0.1 dB and phase imbalance is better than +/-0.5 deg. (Fig. 4), resulting in image rejection of better than 50 dB. Such high sideband rejection eases the requirement for digital calibration in a zero- IF implementation.

The ADL5380 I/Q demodulator was designed to cover 0.4 to 4.0 GHz with 500-MHz baseband bandwidth. It exhibits low noise figure of 13 dB to 3 GHz and -10 dBm of RF input power level. In blocking conditions, the noise figure holds well at less than 17 dB for an input power as high as 0 dBm RMS. Assuming the front-end gain is 25 dB, this means good resilience for blockers of -25 dBm at the antenna.

The demodulator reaches 1-dB compression with at least +11 dBm input power and has an input thirdorder intercept point of better than +25 dBm. The dynamic range, or delta between compression point and noise floor in a 20-MHz bandwidth is close to 100 dB, making this circuit suitable for broadband 3G/4G multi-carrier systems. The design and layout of the I/Q demodulator interface to the ADC is critical to ensure good I and Q signal balance. Anti-alias filter component tolerance, as well as tight control over the differential traces length is critical for a successful design.

Further DC offset cancellation and image correction can be achieved in the digital domain following the ADC's digital conversion. This example direct-conversion receiver employs the 16-b AD9269 pipeline ADC. It implements an integrated DC offset and quadrature error-correction scheme. The algorithm estimates I and Q signal DC offset, gain and phase mismatches, and applies a correction vector to null the gain imbalance using a frequency- independent adaptive correction loop. It corrects as much as +/-1 dB of amplitude error and +/-1.8 deg. of phase mismatch, which is more than sufficient to correct for I/Q demodulator residual imbalances as well as from other sources like the baseband filter or ADC input stage. Algorithm convergence is enhanced due to the already low level of impairments of the I/Q demodulator.

To complete the calibration scheme, the AD9269 also integrates a DC nulling notch filter with adaptive cut-off frequency. It helps eliminate the unwanted DC offset components.

To demonstrate the viability of a direct-conversion solution, the receiver of Fig. 1 was built and characterized using components from Analog Devices. It was designed using two ADL5521 LNAs, the ADL5380 I/Q demodulator, a baseband DGA, and the AD9269 dual ADC. The input modulated RF signal was generated using a directconversion transmitter built around the AD9122 dual digital-to-analog converter (DAC) and ADL5375 broadband quadrature modulator. With a total receiver gain of 28 dB and the AD9269 SNR of 76 dBFS, no AGC was needed to maintain high receiver sensitivity while accommodating in-band blockers to -25 dBm. A discrete fourth-order lowpass LC filter with 30-MHz cutoff frequency was designed to properly attenuate out-ofband noise and support to 40 MHz of complex demodulation bandwidth (see table).

The AD9269 dual ADC running at 80 MSamples/s in this example only dissipates 400 mW, about 100 mW lower than an equivalent IF sampling ADC running at 120 MSamples/s. When constant tracking of impairments is not needed, the AD9269's automatic correction can be frozen to further save power.

The receiver was tested in a multicarrier configuration using WCDMA vectors (Fig. 5). The RF signal at the first LNA input is made of two adjacent WCDMA signals with the strongest signal 62 dB above the weakest, at -56 dBm. An unmodulated blocker at -25 dBm is also added. In this condition, the receiver was capable of demodulating the faint WCDMA carrier down to -118 dBm. This meets the 3G standard sensitivity level in a much more stringent blocking environment. Not including the CW blocker present, the receiver can demodulate WCDMA signals down to -124 dBm in the presence of additional stronger carriers to -52 dBm, with the AD9269 image correction loop running. This corresponds to 6 dB margin over the 3G standard sensitivity requirement.