More in Learning Resources

  • Nov 18, 2014
    webinar

    Switch Mode Power Supply Measurements and Analysis using Oscilloscopes

    Learn how to gain greater insight into the performance and efficiency of switch mode power supplies using oscilloscopes....More
  • Nov 12, 2014
    webinar

    Ten Oscilloscope Innovations You’ll Want that Didn’t Exist Three Years Ago

    Human interface design of modern electronics have dramatically improved to increase productivity. In parallel, oscilloscope user interfaces have had radical improvements to speed debug and analysis....More
  • Oct 23, 2014
    webinar

    PAM-4 Solutions for Transmit and Receive Design Characterization

    400 Gb/s links will be the next step in the continuing need for increased network bandwidth in data centers. Multi-level signaling formats such as PAM-4 are an enabling technology to implement 400G....More
  • Oct 21, 2014
    webinar

    MIPI M-PHY, D-PHY and C-PHY Receiver Testing - Today and Tomorrow

    The mobile industry benefits from standards for hardware and software interfaces for mobile devices established by the MIPI Alliance. Data rate extensions of existing D-PHY and M-PHY interfaces, as well as the recently published multiple bit/symbol C-PHY interface, meet demands for higher aggregate bandwidth....More
  • Oct 30, 2014
    webinar

    SuperSpeed USB 10Gbps (USB 3.1) Physical Layer Test Challenges

    Driven by the demand for more bandwidth, high speed digital standards continues to evolve to higher data rates. The USB 3.1 specification delivers more than double the practical data rate compared to the current 5 Gbps USB 3.0, by implementing a more efficient data encoding scheme. This results in even tougher requirements for the physical layer to ensure interoperability at 10 Gbps....More
  • Sep 11, 2014
    Datasheet

    Coaxial Connector Frequencies (.PDF Download)  

    Coaxial cable connectors are a fundamental component for interfacing with RF devices up to hundreds of gigahertz. The frequency handling capability of...Download Now...More
  • page

    References & Tools

    This section of the site includes useful graphics, charts, and explanations of basic MW&RF design concepts....More
  • Nov 6, 2014
    webinar

    How to Achieve Compliance to the New 1E-16 BER Contour Spec in DDR4

    For the first time in a DDR standard, JEDEC has included in a BER contour spec for DDR4. The eye opening of the 1E-16 BER contour of DQ lines must not violate the mask. This specification presents new simulation and measurement challenges....More
  • Oct 29, 2014
    webinar

    Measuring Power Rail Signal Integrity with Oscilloscopes

    Power rails play a critical part in today’s electronic device development. The need to see and characterize small disturbances on rails is increasing as are the challenges to make these measurements. Attend the webinar and learn what scope attributes—from the acquisition engine to the probe tip—enable more precise and comprehensive testing of power rails....More
  • Sep 25, 2014
    webinar

    How to Optimize Your SerDes Design During the Pre-layout Phase

    In the era of receiver equalization, older stackup and controlled impedance line design tools are obsolete because the metrics that output (frequency response) are irrelevant. The metric that matters today is the post-equalization eye opening....More
Whitepapers

Increase Power Amplifier Test Throughput with the Keysight PXIe Vector Signal Generator and Analyzers
Sponsored by Keysight Technologies
Download this white paper


Poster Worldwide Spectrum Allocations
Sponsored by Tektronix
Download this white paper


Achieving Excellent Spectrum Analysis Results Using Innovative Noise, Image and Spur Suppression Techniques
Sponsored by Keysight Technologies
Download this white paper

Webcasts

Optimizing 100G Ethernet Electrical Measurements
Tue, November 5, 2:00pm EST
Sponsored by Keysight Technologies

Register Now!

Connect With Us

Sponsored Introduction Continue on to (or wait seconds) ×